It sounds like you have it hooked up correctly. If your pump is not connected you also will need you get your pump out of the shred or the basement and get that out to the area where the pool filter system is to be hooked up. Follow these directions to install, check and maintain your above-ground pool filter in good operational condition. This page shows a diagram of a typical center drain installation on an above ground pool. Then you will want to take the other end of the hose and connect it to the bottom of the skimmer. We are losing water approx 2 to 7inches. The water is pumped in through the hair and lint pot and pushed out through the other pump opening, usually going out the top, or maybe the side, of the pump.
This basket catches finer debris that the skimmer basket misses. Hose Placement for Above Ground Pools by Billie Lindsey Can you please tell me the hose placement for the above ground pump and filter. The picture at left shows the two major components of a typical sand filter: the Filter Tank and the Multiport Valve and piping assembly. Be careful when leveling the sand that you do not lift the pipe and lateral assemble up off the bottom of the tank. I forgot to write it down last year when I took the off of the pool. After the primer dries, apply a thin even coat of glue to both surfaces. I seem to have forgotten what goes where with the hoses.
Step 2 — Installation Begin by ensuring that the cartridge is securely installed. Folks put the following video to. Keeping up with your pool will keep it from draining energy your entire summer. With the filter running look into the lint pot lid and see if there are any air bubbles. Once you have the pump, the filter and the hoses you will be ready to connect your above ground pool filter to the pool. The center drains and the skimmer are all suction devices and need to hook up to the pump.
Last summer escapes 10: need to add smart control with clips. You said you have the filter going to the pool intake, I assume you mean the pool return, the place where the water goes back into the pool. Water leaves the pool and is flushed through this section to purge the filter of dirt and grime. Or give us a call at 407-834-2200, and we would be happy to take your order by phone. You will also want to tighten these hose clamps after you install the hose between your above ground skimmer and the front suction side of the pool pump. Water leaves the pool and enters the filter to be cleaned.
The hose coming off the front of the pump needs to connect to valve assembly, or a pipe coming off it, and the skimmer hose connects to the other side of the valve. Pour sand carefully into the pool sand filter until laterals are fully covered. If you have a pool heater, the pool filter will release water to the heater before going to the chlorinator. J-Hook sidewalls - for the pool. You will need to tighten down the hose clamp with your screwdriver. Finally, make sure that your filter pumps power supply is grounded as it should be.
Have an electrician install and connect the filter's electric motor for safety and to validate your filter's warranty. Pool water will come in through the pool pump, be filtered through the sand filter and released to the chlorinator before returning back to the pool. Pool Filter Hookup We have a Hayward cartridge filter and a main drain for our 24 foot above ground pool. Most above ground pools have a skimmer that would have a basket in them for catching the leafs. Leaving them out is not a problem.
Most above ground pool pumps have a hair and lint pot, this also has a basket inside of it. The outflow hose sucks water out of the pool, toward the filter. Use a wrench on the square nut on the final turns. The filter normally looks like the filter of a car, designed to trap debris and smaller matter. Connecting the Pump discharge to the filter: Most above ground swimming pool systems like will use a union between the pump and the filter as you can see in the above picture.
Your pressure problem could be from a couple of different reasons. You should have three hoses, the long ones are the intake and return hoses. A swimming pool filter helps maintain clean and healthy pool water. After you have connected both ends you will want to tighten the hose clamps thoroughly. Winterizing your above-ground pool requires you to drain the sand filter and the pump. Many Thanks, Billie Lindsey Hi Billie.
New liner installation — hookup and chemical pumps are the right swimming above ground swimming pools, filter up a normal sand pool services. It has two valve shut offs and do we have to go through the heater? Make sure the pipe and inside of the adapter are clean. The second connection you will need to make is to connect the top of the pump to the in on your filters multi-port valve. You will not be able to push the pipe back down without causing the laterals to rotate up. I think I might have the hoses hooked up wrong.
If the threads aren't prepared, wrap them with two layers of Teflon tape. An example is pictured at left. When installed, the valve sets on top of the tank and the vertical pipe the lateral assembly are inside the tank. A properly functioning above-ground pool filter is a vital element for the cleanliness of your swimming pool. Be sure to empty your skimmer basket weekly and use a net to dispose of excess bugs and leaves. The clean water then gets pushed back into the inflow hose and back into your pool toward the top of the pool.