You can buy any of the parts offered from our physical Sales Counter at Torquepower, Brisbane, Australia but the Online special pricing is reserved for Online purchases only. Low power or rough idle. Some Cummins engine fault codes include 111, which indicates an internal engine control unit failure; 214, which indicates that the engine's oil temperature is too high; and 434, which indicates that power was lost while the ignition was off. Possibly no noticeable performance effect, or possibility of rough idle. A low signal voltage is detected in the dosing system air circuit.
Component Location Mounted in air intake horn. Description: Critically low level liquid for cleaning exhaust gases in the tank. High air pressure was detected in the dosing unit when charging the system, when a close signal was given to the dosing unit air valve. Progressive power derate with increasing time after alert. If you are tired of browsing the Internet looking for Cummins fault codes, then relax. Voltage should only appear in one of the circuits. Description: A low voltage is detected in the starter lock circuit.
Engine diagnostic switch blink codes f. Description: The fluid controller in the exhaust gas cleaning system of diesel engines determines that the voltage on the main line heater exceeds the value specified in the calibration. If active, there is a faulty sensor. Description: The fluid injection controller in the exhaust gas cleaning system of diesel engines determines that the heater voltage exceeds the value specified in the calibration. The codes were gone and everything was back to normal.
We will calculate freight costs at cost and add it to a pro-forma invoice which will be sent to you for secure payment. Cummins engines use fault codes to let operators know that the system is not functioning properly. If code is not active, engine harness has an open or shorted Supply circuit. Torquepower has specialized in Cummins engine parts and support since 1978. All of the temps looked perfect and it passed all of the tests. Description: The exhaust gas cleaning control system has determined that the temperature of the exhaust gases during the active regeneration of the particulate filter of the exhaust gas cleaning system is not high enough. Repair: If code is inactive, troubleshoot inactive or intermittent fault code.
The engine will only idle. Engine will only run using the front three cylinders. Progressive power and speed derate. No engine protection for oil temperature. Description: No particulate matter filter. Repair complete, disable fault code.
Attempt to start the engine without permission of the anti-theft system. Description: A pulse width modulated signal with a level equal to the system supply voltage when this signal is turned on is not detected in the fuel system actuator valve circuit. View Cummins in engine performance wiring diagrams to identify connector terminal. Description: The exhaust gas cleaning quality sensor detects that the fluid concentration has increased above the critical threshold. The shop diagnosed the truck with a bad particulate sensor. Possibly white smoke, fan will stay on.
On vehicles equipped with the Cummins RoadRelay system, the operator receives an audible alarm indicating that a fault has occurred. Description: The drive changes the geometry of the turbocharger has detected an internal error in the logic controller of the turbocharger. To remove soot, regeneration of the exhaust gas cleaning system is necessary. Other Engine Groups cover Filters, Belts, Silicon Hose and Cummins Merchandise. Engine will only run using the rear three cylinders. Engine will return to idle speed. The current detected on the nozzle 2 when the voltage is off.
Description: The liquid dosing unit for diesel engine exhaust systems cannot maintain the specified fluid pressure for diesel engine exhaust systems. Description: An error was detected between the exhaust gas recirculation system differential pressure sensor signal or the sensor did not pass the auto-zero test. Engine will only run using the front three cylinders. No engine protection for oil pressure. Progressive power derate with increasing time after alert. Description: The malfunction code is registered in the presence of disappearing failures of a chain of the executive valve of the fuel pump.
Refer to the appropriate fault code troubleshooting tree. Description: The position of the actuator during initial power-up is not determined by internal means due to the mechanism jams or internal faults. Possibly hard starting, low power, white smoke. You can buy any of the parts offered from our physical Sales Counter at Torquepower, Brisbane, Australia but the Online special pricing is reserved for Online purchases only. If the engine is www. The current detected on the nozzle 4 when the voltage is off. Clear the inactive fault codes.
If the error has occurred but is not happening at the time of diagnostics, it is known as an Inactive Fault. You can also find what you want by Part Number or Description. Description: The fluid injection controller for the exhaust gas cleaning system detects an open circuit or a short to ground in the main line heater circuit. Description: The readings of the temperature sensor No. When a fault code has been activated, the operator is alerted to the condition through an audible or visual alarm.