Install the bearings A and bearing caps B with 12. If you get the service manual download from the company itself, it will be updated as the technical service bulletin gets more information. Remove the piston from the cylinder block see piston pin. However, Honda recommends that all maintenance services be done at the recommended intervals to ensure long-term reliability. Make sure the vehicle is on level ground. Connect the alternator 4P connector terminal No. Perform all calibration procedures, except test-driving, in the service bay.
However, Honda recommends that all maintenance services be done at the recommended intervals to ensure long-term reliability. The repair bulletin can be added to the repair manuals as they are made available. Hang the steering gearbox with a rope to the frame. When worn or area damaged At 4th gear 52. Make sure you have the anti-theft code for the radio 5. Check and, if necessary, adjust the valve clearance on No.
If the engine is still in the vehicle, drain the engine oil see page 8-5. Loosen the grommet mounting nuts B , and turn the grommet C counterclockwise, then pull out 16. Apply a light coat of new engine oil around the 5. Apply new engine oil to the main bearings and rod 1. However, Honda recommends that all maintenance services be done at the recommended intervals to ensure long-term reliability.
Remove the connecting rod cap and bearing half complete bearing with the same color code, and see page 7-12. Adjust the seat recline to the forwardmost position. The best service manual pdf of Honda Odyssey 2008 2009 2010 comes from its manufacturer. Disconnect the floor wire harness 4P connector A from the seat belt tensioner. After installing a new set of rings, measure the mark and the second ring B has a 2C mark. Factory highly detailed repair manual's, with complete instructions and illustrations, wiring schematics and diagram's to completely service and repair your vehicle. Do not position yourself in front of the airbag during removal, inspection, or replacement.
Remove the exhaust pipe A see step 32 on page 5- 3. Inspect the rocker arm piston A. Be sure to pull on the sleeve and not on the connector half. Calculate the difference between the cylinder bore 1. Draw alignment marks on the front subframe.
Hold the auto-tensioner A with the maintenance 9. Torque the bearing cap bolts A , then torque the then install the cap. Heat the piston and connecting rod assembly to approximately 158°F 70°C , then remove the 1. Support the stator housing in a vise, and drive out Rectifier Test the front bearing with a brass drift A and hammer. With a hammer and commercially available tools rear bearing, go to step 18. Be sure to pull on the sleeve and not on the connector.
Place the prepared weight on the front passenger's seat. Remove the cylinder head covers. It gives you the manual for your Odyssey and it's very easy to use. Be sure the battery connections are good, and that the battery is sufficiently charged. Replace the camshaft if any lobes are pitted, head.
During installation or replacement, be careful not to bump by impact wrench, hammer, etc. Remove the four bolts, then remove the rear 9. Make sure the front passenger's seat is dry. Install the fuel feed hose A and fuel return hose B , using new washers C. Remove the brake booster vacuum hose A. They are specifically written for the do-it-yourselfer as well as the experienced mechanic. Pull the cable so that the adjusting nut B touches the bracket, and tighten the locknut A.
If you find a term or abbreviation in a 2001 or later manual that is unfamiliar to you, check this list. In the dark old days of auto repair, you had to buy a traditional service manual in book format which would retail at a higher cost. If they do not move smoothly, replace the rocker arm assembly. Check the wheel alignment see page 18-5. Push the crankshaft firmly away from the dial indicator, and zero the dial against the end of the 2. Warm up the engine to normal operating 8.
Intake Valve Dimensions Intake Valve Dimensions A Standard New : 33. If the oil level is correct: 1. Raise the engine speed above 1,000 rpm. Remove the steering gearbox mount from the front subframe. With the battery positive terminal still connected to 24. Apply new engine oil to the piston pin snap rings A and turn them in the ring grooves until the end gaps are lined up with the cutouts in the piston pin bores B. Never tow the vehicle behind another pivoting arms that go under the tires front or rear and vehicle with just a rope or chain.