What can require 55 ft-lb torque dry, only needs 30 ft-lb lubed. I just put my second set of tires on the car, because I was misled by the tire dealership. Bought this car with 112,000 miles on it. Data Unavailable Third Shoulder Room in. I am now going to replace the stereo, with a new one from Amazon, as well as placing some more upgrades, like window tint, and dashboard kits. Turns out the bumper I ordered was just what I needed. This is typically measured in liters 3.
Do not modify this for your own safety. It will case the torque to go over you max. If there are 5 lugs: tighten lug at 2 o'clock position to 7, then to 12, then to 4 then to 10. Then had an issue with one of the main Catalytic converters on the engine block, bought a new one from Ebay, as well as an Air conditioner condenser, Since I changed out the air conditioner unit, I had new belts put on the car. You can use regular grade in your engine and it will not harm it at all. Lastly, try to install in the cross pattern.
You can figure it cross-threading out with some basic formula but no need to. So by lowering the friction it will increase the torque for that thread. Lastly, try to install in the cross pattern. The bumper was packaged in a relatively large box. If not, do not worry that much. I used ge silicone 2 clear, make a bead all the way around, took about ten minutes, could not be better.
. Data Unavailable Third Hip Room in. Also make sure you put some lube on the threads. To sum it up, each lube lowers the coefficient of friction. I changed out the tires, brakes, and battery to start.
This is at least 80% over torqued condition. All you will notice is slightly slower acceleration and a slight drop in engine horsepower. Also make sure you put some lube on the threads. It will increase the torque by a small percent 3 to 8 but it will not harm the threads cross threading etc. Modern engine management systems have knock sensors that detect lower grade fuel and make the necessary adjustments to your timing and fuel delivery systems. I know this works, I just reset mine a few minutes ago.
It will cruise at 80mph all day without breaking a sweat, feels like 50mph. As with any car of this age, there is the expected regular maintenance and repairs, but the cost is not extreme like it might be with certain German cars. It's basically a Toyota Camry with frosting poured on it, very economical, easy to source parts for, and to work on. I was told the car computes tire rotations and since a low pressure tire takes more rotations than a fully inflated tire, the computer puts up a message on the dash. The torqued values given are from the manufacturer are for dry conditions.
Two degrees in Mechanical Engineering and a career in machine designing gives me the qualifications for these statements. Also check lexus owners club for more detail. Agree with completely Also, I set torque to 65 ft. Posted on Dec 24, 2009. If not, do not worry that much.
After the above operation, the master warning light comes on, a warning tone sounds and the message appears to inform you that the engine oil maintenance data has been reset. Data Unavailable Third Leg Room in. MacPherson Strut Suspension Type - Rear Data Unavailable Suspension Type - Rear Cont. It will increase the torque by a small percent 3 to 8 but it will not harm the threads cross threading etc. Anything is better then nothing. Like some are moly based, silicone, alum-oxide, etc.
I drove a Toyota with over 342,000 the other day, and it drove great. I sure hope nobody followed this advice for adding lube to the studs. I have bought the new halo headlamps to replace the originals, since they are turning yellow, also purchased on Ebay at a great price. Depress and hold until the message on your dash goes out and you are good to go. Just try to remember the torque formula in case you torque to max, which is perfectly fine, and add a certain lube.
I have 168,000 miles on it so far. I-4 and V-6 refer to the configuration and number of cylinders. Gas mileage is decent for a mid-size V6, I get about 26. It has decent power for leading traffic on the freeways. If there are 5 lugs: tighten lug at 2 o'clock position to 7, then to 12, then to 4 then to 10. When I opened the box the bumper was covered well in bubble wrap and the sides of the bumper were folded with tape.