The best thing to do when selecting new leaf springs for F-150 is to get the spring code off of your door panel as you can see above. Thanks for the help everyone, It doesn't pay to take pictures right now because it is dark out but I just looked at the door jam and the weight is 8600. Can anyone help me out? Hello all, I have been searching through here and the internet in general and I really cannot get a definitive answer. The open knuckle, monobeam, Dana-Spicer Model 60 using Ball Joints instead of King Pins was introduced by Ford for the 1992 model year F-350 1 ton 4x4. I didn't purchase the drop brackets and the suspension arms were at way too much of an angle which was going to cause many problems both ride quality wise and wear on. One end of this spring will attach directly to the hanger with a suspension bolt. The exception is the inner axle shaft and slip yoke on the passenger side.
Because springs can sag and elongate as they wear, this new spring may not exactly match the old one, and the alignment of your truck could be affected. See more information at the bottom of this page. You may choose to replace old suspension bolts as well. Axle Pivot Brackets - Tuff Country 20852 Rating: 4 Stars I added the Tuff Country leveling add-a-leaf leaf spring to the front of my truck which it desperately needed to bring the front up to the level of the rear. Need assistance selecting the right Tuff Country product? The other end will attach to shackle straps that are suspended from a hanger. If you are simply replacing a spring, you may still have hangers welded onto your truck.
We're here to help - please call us at 1-800-358-4751. It is recommended that you replace the other leaf spring in your setup at the same time. That means the maximum legal weight sitting on those 4 tires is 8800lbs assuming you have not registered the tags for a lower weight So now you need the weight of the truck as equipped to travel with passengers, full tank of fuel etc. Each spring flexes to absorb road shock as you travel, allowing the axle to move somewhat independently of the rest of your truck. Listed below are the Axle Pivot Brackets that are designed to work with the 1997 Ford F-250. To mount this spring, you will need hangers, shackle straps, and suspension bolts. You should, however, replace your shackle straps because they are usually the first component to wear out.
This will ensure that the spring you choose has the proper amount of leaves, arch, width, etc. The early right diff output shafts could be pulled without removing the differential housing from the axle beam with a special slide hammer puller attachment, but seal replacement also requires the bearing be replaced. Later production axles use a straight roller bearing pressed into the differential housing and the axle shaft is retained by a snap ring inside the differential next to the differential side gear. Tell us what you need or were expecting to find. My truck has the 351W in it with an e40d trans and 4.
You can send us a or call us to help you select the best spring for your application. I just bought a 1995 F250. We stock a wide selection of parts and Tools for 1992 to 1997 Ford F-350 Dana 60 open knuckle front drive axles with Ball Joints. Leaf springs are an integral part of your Truck suspension system. For spring numbers without pricing, us to provide pricing and availability.
If you have any questions about spring selection please feel free to call us or email to us:wabco wabco. After 1983, these axles were held in place by an internal c-clip. Is that definitive or should I look at what the front axle says? Ford used the axle through the end of the 1997 model year when the F-350 line was dropped and replaced by the 1999 F-350 Super Duty which initially only had a Dana 50 MonoBeam front Axle. . Please review the vehicle options and installation notes, to ensure you select the correct product for your Ford F-250. The new axle, which is rated for a 5,000-pound capacity was the first production Dana 60 front axle to use Ball Joints, but it still had serviceable wheel bearings and lockout hubs like the previous 1985-1991 King Pin axle. This helps to reduce wear and tear on the truck and also ensures a smooth ride.
To determine the type of hanger kit that you need, you must know the specific type of leaf spring that you have, as well as your axle capacity. Depending on the hanger kits used with them, springs can be configured to work for single-, tandem- or triple-axle applications. Don't forget to include your email address if you'd like a reply from us. The early axles use a pressed-on taper roller bearing and an external bolt-on retaining flange. The larger the F250, the lower the carrying capacity due… That depends upon the frame size and the number of tires. If you have a tandem- or triple-axle truck, the shackle straps will be attached to the equalizer that connects multiple springs. Double-eye leaf springs attach to hangers that are welded onto your truck.
Shop now for Parts, Tools, and Manuals to fit 1992-1997 Ford F350 4x4 Trucks with Dana 60 Open Knuckle Front Axles. These straps allow the spring to move and pivot so that it can better compensate for uneven pavement. They did not use no coil springs and radius arms like the Ford F-150. If you are fabricating a truck, you will need to purchase a hanger kit for installation. Many of these springs are in stock or can be made in a short lead time.
. . . . .
. . . . . . .